ASTM A956 PDF

A – 02 Standard Test Method for Leeb Hardness Testing of Steel Products, Dynamic Hardness Test, Equotip, Equotip Hardness Test, Leeb, Rebound. A/AM – 17 Standard Test Method for Leeb Hardness Testing of Steel Products, dynamic hardness test, Equotip, Equotip hardness test, Leeb, rebound . ASTM A – Download as PDF File .pdf), Text File .txt) or read online.

Author: Dousar Moogunos
Country: Portugal
Language: English (Spanish)
Genre: Spiritual
Published (Last): 12 May 2012
Pages: 347
PDF File Size: 1.61 Mb
ePub File Size: 16.39 Mb
ISBN: 292-3-91826-933-5
Downloads: 96993
Price: Free* [*Free Regsitration Required]
Uploader: Kegul

Measurements on steel and cast steel.

ASTM A – Free Download PDF Ebook

These induced voltages are proportional to the respective impact and rebound velocities. Impact bodies show minimal wear even at high hardness levels when compared to D device. All such conversions are, at best, approximations and therefore conversions should a596 avoided except for special LE -5 -9 -4 -9 -4 -9 -4 -8 -4 -8 -4 -8 -3 -7 -3 -7 -3 -6 -3 -6 -3 -5 -9 -2 -5 -8 TABLE 1 Correction Values for Other Impact Directions: Probe S LS -4 -4 -4 -4 -3 -3 -3 -3 -3 -2 -2 -5 -7 -5 -8 -5 -9 -6 -6 -7 -7 -7 -8 -8 -9 max.

The measurement readings determined by the latter method are erroneous due to gravitational acceleration and are not independent of direction. Each of the standard probes has its own characteristic direction dependency, which is determined by: The respective standard deviations among test results, related to the above numbers by the factor 2. astk

ASTM A956-06.pdf

The main reasons for this are: Historical Version s – view previous versions of standard. Significance and Use 4. Link to Active This link will always route to the current Active version of the standard. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. The indicated value is automatically a9566 with the next test impact result.

  PIYANO METODU PDF

The impact devices D and E have become industry standards for general purpose applications since the first introduction of the D-device in Home Tags Login Register Search. A number in parentheses indicates the year of last reapproval. Please fill this form, we will try to respond as soon as possible.

At temperatures outside this range, the user shall develop a temperature correction for the specific material being tested. The impact device, while not in contact with the test piece, is held firmly with one hand and the charging tube is depressed with the other hand until contact is felt. Same materials to be tested like standard D unit but at extended hardness range. Please help us to share our service with your friends.

The impact and rebound velocities are assumed to be proportional to the extreme values A and B of the signal curve. A number in parentheses indicates the year of asym reapproval. The impact body is now in its loaded or locked position. Failure to provide adequate support and coupling will produce test results lower than the true hardness value.

Both effects lead to a change in impact energy.

ASTM A956-12

Same materials to be tested a9956 standard D unit but at extended hardness range. Any paint, scale, pits, or other surface coatings shall be completely removed. Applications on surface hardened components. Each laboratory measured the hardness of each block 25 times. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Only the mass must be kept within narrow tolerances. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

  BEHRINGER MICROMON MA400 HEADPHONE AMPLIFIER PDF

Impact bodies show no wear even at high hardness levels when compared to D device. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards. The impact and rebound velocities are assumed to be proportional to the extremal values A and B of the signal curve, which is a good approximation, if the device is constructed so, that the extremals are atm the signal step caused by the impact.

The results generated at that location do not represent the part at any other surface location and yield no information about the material at subsurface locations. Requires better surface finish than impact device D. The measurement readings determined by the latter method are erroneous due to gravitational acceleration and are not independent of direction. For the definition of some of the parameters refer to Fig. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

Verification 9a56 Apparatus 7. The results generated at that location do not represent the part at any other surface location and yield no information about the material at subsurface locations.

Device DL LDL -3 -3 -2 -2 -2 -1 -1 -1 -2 -3 -6 -2 -4 -7 -3 -5 -9 -3 -6 -4 -7 -5 -8 -5 -9 -6 We need your help! The quotient of these measured voltage values derived from the impact and rebound velocities, multiplied by the factor produces a number which constitutes z956 Leeb hardness value.

Please fill this form, we will try to respond as soon as a95.