ASTM B210 PDF
B – 02 Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes, aluminum alloy, aluminum-alloy drawn seamless tubes. ASTM B Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes. Drawn Aluminum Tubing from TW Metals is a magnesium and silicon alloyed aluminum product with good corrosion resistance and formability. Call now!.
|Published (Last):||27 April 2016|
|PDF File Size:||14.77 Mb|
|ePub File Size:||17.19 Mb|
|Price:||Free* [*Free Regsitration Required]|
When specified, heat treatment of applicable tempers shall be in accordance with practice B E Others includes listed elements for which no specific limit is shown as well as unlisted metallic elements. F Other elements Total shall be the sum astn unspecified metallic elements 0.
Alloy F O 0. H The aluminum content shall be calculated by subtracting from Alloy Alclad F O 0.
The different methods for leak testing of tubes are presented. C For purposes of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit, in accordance with the rounding-off method of Practice E Note 2—Throughout this specification, use of the term alloy in the general sense includes aluminum as well as aluminum alloy.
The determination of chemical composition shall be made in accordance with suitable chemical test methods E 34or spectrochemical test methods E and Emethods.
A Limits are in weight percent maximum unless shown as a range or otherwise stated. The tube b201 conform to the tensile property requirements specified.
The tubes shall conform to the chemical composition requirements specified. B Analysis shall be made for the elements for which limits are shown in this table.
Aluminum Tubing – AMS-WWT/6, ASTM B, AMS-T, , , | TW Metals
The tension tests shall be made in accordance with test methods B M. Coiled tubes are generally available only as round tubes with a wall thickness not exceeding 0. Alloy Alclad F. I Alloy clad with Alloy It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
ASTM B210 Aluminum-Alloy Drawn Seamless Tubes Manufacturer
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Link to Active This link will always route to the current Active version of the standard. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A for aluminum designation in accordance with Practice E Should any analysis by the producer or the purchaser establish that an Others element exceeds the limit of Each or that the aggregate of several Others elements exceeds the limit of Totalthe material shall be considered non-conforming.
This specification covers aluminum and aluminum-alloy drawn seamless tubes in straight lengths and coils for general purpose. This abstract is a brief summary of the referenced standard. Historical Version s – view previous versions of standard. The tube shall be produced by drawing an extruded tube made from hollow extrusion ingot cast in hollow form or pierced and extruded by the satm of the die and mandrel method.
The samples from ast, tube shall not be required to conform to these limits. Work Item s – proposed revisions of this standard. Aluminum F O 0.
6061 Drawn Aluminum Tubing
T4, T42 H 0. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract h210 accurate, complete or up to date.
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Flattening test specimens shall be flattened sidewise under a gradually applied load so as to give a uniform radius of bend until the minimum outside diameter under b2110 is not more than F times the wall thickness of the b120 as specified.
J Composition of cladding alloy as applied during the course of manufacture. Tensile Strength, ksi Yield Strength D 0. However, such analysis is not required and may not cover all metallic Others elements. The producer may analyze samples for trace elements not specified in the specification.