ELIWELL ID970 PDF

Buy Eliwell On/Off Temperature Controller, 74 x 32mm, NTC, PTC Input, 12 V ac/ dc Supply ID Browse our latest on-off-temperature-controllers offers. Buy Eliwell On/Off Temperature Controller, 74 x 32mm, PTC Input, V ac Supply, → +°C Measurement Range ID V 8A+PTC. Browse our. In order to configure the instrument for this purpose you must access the folder identified by the “Add” label and use the parameters “dEA” and “FAA”. ID LX.

Author: Toshakar Zuluzilkree
Country: Russian Federation
Language: English (Spanish)
Genre: Education
Published (Last): 27 April 2004
Pages: 219
PDF File Size: 15.81 Mb
ePub File Size: 14.28 Mb
ISBN: 676-8-32925-247-7
Downloads: 44615
Price: Free* [*Free Regsitration Required]
Uploader: Bar

Programming parameter transfer from Copy Card to instrument. All the versions are provided with a TTL connection in order to use Copy Card, the quick programming accessory.

Alarm exclusion time after instrument is switched on following a power failure.

It is still possible to enter parameter programming and modify the parameters, including the status of this parameter, in order to allow keyboard unlocking. Users must not be able to access parts with dangerous voltage levels under normal operating conditions.

Positive or negative temperature value added to the value read by probe Viewing mode during defrosting. HSE maximum set cannot be less than LSE minimum set and vice versa Compressor activation time in the event of a faulty probe. The password is enabled if the value of the PA1 parameter is not 0. Single stage controller for temperature. Defrost counting is always active when the machine is on and starts at each power-on. View with decimal point.

  HCMS 3917 PDF

Any protection devices required to comply with product requirements or dictated by common sense due to obvious safety reasons should be installed externally. At the end of the lamp test, the following messages are displayed for about 5 seconds: At least the indicated time must elapse between switch-off of the compressor relay and the successive switch-on.

Temperature alarm signal delay time. Download from reset Connect the copy card when the instrument is OFF.

Set point setting folder; -Pb1: The parameter indicates that a protection is active on the relay actuations of the generic compressor. The Setpoint can also be viewed. Temperature value understood as distance from the Setpoint or as an absolute value based on Att which if exceeded in a downward direction triggers the activation of the alarm signal.

The programming parameters are downloaded when the device is switched on. It is classified as follows: There are 2 operating modes determined by parameter AtP: If one or more parameters are modified, it is suggested to the switch off the controller after the modification and then switched back on. Delay time in activating the outputs after switch-on of the instrument or after a power failure. The indicated time must elapse between two subsequent switch-ons of the compressor.

Minimum possible setpoint value.

Eliwell ID MC (Milk) |

For higher loads, use a suitable contactor. Eliwell reserves the right to make any changes or improvements without prior notice and at any time.

Temperature value understood as distance from the Setpoint or as an absolute value eliwelk on Att which if exceeded in an upward direction triggers the activation of the alarm signal.

  HET SPEL NEIL STRAUSS PDF

The device must be suitably protected from water and dust according to the specific application and only be accessible using special tools except for the front keypad. Single stage controller for temperature ID The operation cannot be cancelled. Always switch off machine before working on electrical connections.

The parameter indicates that the protection is active on compressor relay actuations.

It’s a community-based project which helps to repair anything. The continuous improvement of our products can cause some variations in this non contractual document even without notice.

Between the request and effective activation of the compressor relay, at least the specified time must elapse. Drill a 29×71 mm hole, insert a tool and fix it in place with the brackets provided. Erasing all parameters in the key. Although Eliwell has taken all possible measures to guarantee the accuracy of this document, it declines any responsibility for any damage arising eliewll of its use.

Programming parameter transfer from instrument to Copy Card.

Eliwell ID970 MC (Milk)

Compressor off time in the event of a faulty probe. The two sets are interdependent: The instrument has screw terminals for connecting electrical cables with a maximum diameter of 2. For this page to function properly, you must enable JavaScript. Defrost cycles can be controlled at time intervals.