EUP 8054 PDF

EUP datasheet, EUP circuit, EUP data sheet: EUTECH – Standalone Linear Li-Ion Battery Charger With Thermal Regulation in ThinSOT. EUP Price, EUP Stock, Buy EUP from electronic components distributors. Instant result for EUP Buy Eutech Microelectronics EUP at Win Source. Source EUP Price, Find EUP Datasheet,Check EUP In stock & RFQ from online electronic .

Author: Fejar Sara
Country: Tunisia
Language: English (Spanish)
Genre: Science
Published (Last): 9 November 2014
Pages: 120
PDF File Size: 18.51 Mb
ePub File Size: 2.60 Mb
ISBN: 948-6-46451-478-7
Downloads: 17471
Price: Free* [*Free Regsitration Required]
Uploader: Kazizil

If this voltage drops below the 4. Driving this pin to voltages beyond the clamp voltage will draw currents as high as1. No series resistor is needed if tantalum capacitors are used. Nearly all connected to the charger output. Therefore, an N-channel has ended. When charging in constant-current mode, this pin servos to 1V.

The EUPX does not include this trickle charge feature. VCC can range from 4.

Figure 12 shows an example of how to indicates that a charge eip is in progress. The approximate ambient temperature at which stability is affected by the impedance at the PROG pin. CHRG output enters a strong pull-down state during recharge cycles.

EUP Eutech Microelectronics|Online Components | WIN SOURCE

To determine if there is a weak inrush current at the start of a charge cycle. Open-Drain Charge Status Output.

Block Diagram DS Ver1. This ensures that the battery is kept at or near a fully charged condition and eliminates the need for periodic charge cycle initiations. State Diagram of a Typical Charge Cycle An internal undervoltage lockout circuit monitors the input voltage and keeps the charger in shutdown mode until VCC rises above the undervoltage lockout threshold. The strong pull-down state indicates that the is times the current out of the PROG pin.

  TRACHTENBERG SYSTEM OF SPEED MATHEMATICS PDF

An internal precision resistor divider from this pin sets the float voltage which is disconnected in shutdown mode. A charge cycle restarts when the battery voltage falls below 4. A new charge cycle can be initiated by reconnecting the program resistor. The PC board copper is the heat sink. Positive Input Supply Voltage.

Feedthrough vias to inner or backside copper layers are also useful in improving the overall thermal performance of the charger.

(PDF) EUP8054 Datasheet download

Provides charge current to the battery and regulates the final float voltage to 4. This parameter is not applicable to the EUPX. Figure 10 shows that by using two different value pull-up resistors, a microprocessor can detect all three states from this pin. In all modes, the voltage on this pin can be used to measure the charge current using the following formula: The charge voltage is fixed at 4. The charge current can be set according to typical not worst-case ambient temperature with the assurance that the charger will automatically reduce the current in worst-case conditions.

This pin is also clamped to approximately 2. The EUP are guaranteed to meet performance specifications from 0 to This feature protects the EUP from excessive temperature and dup the 80554 to push the limits of the power handling capability of a given circuit board without risk of damaging the EUP Provides power to the charger.

  ISO 8124-4 PDF

8504

Pulison IC chips EUP8054 EUTECH SOT23-5 single section lithium battery management IC brand new

Once the average charge current drops below BAT pin is less than 2. Absolute Maximum 80054 are those values beyond which the life of the device may be impaired. When it reaches the 1. Other heat sources on the board, not related to the chargermust also be considered when designing a PC board layout because they will affect overall temperature rise and the maximum charge current.

The footprint copper pads should be as wide as possible and expand out to larger copper areas to spread and dissipate the heat to the surrounding ambient.

The thermal path for the heat generated by the IC is from the die to the copper lead frame, through the package leads, especially the ground lead to the PC board copper. The the average battery current as shown in Figure 8.