TDA7052 PDF

1W BTL Mono amplifier electronic kit using a TDA IC. Designed for battery- fed portable audio applications. Type, Through Hole. Operating Temperature, -. Supplier Device Package, 8- DIP. Package / Case, 8-DIP (“, mm). Base Part Number, TDA : TDA Amplifier Module 1W (kit): Computers & Accessories.

Author: Akinom Nigar
Country: Antigua & Barbuda
Language: English (Spanish)
Genre: Marketing
Published (Last): 1 April 2010
Pages: 131
PDF File Size: 17.89 Mb
ePub File Size: 12.42 Mb
ISBN: 383-5-38131-833-3
Downloads: 86806
Price: Free* [*Free Regsitration Required]
Uploader: Shasida

That’s how a bridge output works. If the chip still overheats, it could be faulty. Sign up using Email and Password. I should also mention that this is my first circuit on a breadboard, so it could be causing problems too.

The nF has to be ceramic for a reason low ESR. Leonardo Rossi 80 8. How did you measure the output?

amplifier – TDA output DC offset – Electrical Engineering Stack Exchange

It appears that the DC offset of the outputs are not “cancelling out” and that’s why the chip is getting excessively hot. Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

I’ve never had any problems with the TDA Tea7052 speaker is quiet much more than in the radio I got the amplifier and speaker form and from time to time it seems as if the amplifier is clipping I’m not sure if that’s the right tda70522.

  WEST PAKISTAN FAMILY COURTS ACT 1964 PDF

Home Questions Tags Users Unanswered.

My problem is that I’m observing a large DC offset at the audio output, and the IC is getting very hot. All of your parameters mA for bias current for bridge output seem normal and you stated it put out a clean sound, so I do not think anything is wrong-except for a missing heat sink.

I’m feeding in 12Vdc and the tda7502 is drawing around mA, which makes tdw7052 1. The potentiometer fixed the problems with power supply voltage. So, the input is being driven with a signal generator with the parameters displayed. Home Questions Tags Users Unanswered.

Access Denied

You can measure the sound card’s output impedance, but it’s probably low enough to not matter. Post as a guest Name.

You are probably overdriving the amplifier by using a sound card for testing. First problem is that the amplifier won’t work on voltages above 3. If the IC is getting hot, well it needs to be mounted to a heat sink.

I also used nF electrolytic capacitor, since I don’t have any ceramic at the moment. The TDA was designed for an 8 ohm unit. Sign up or log in Sign up using Google. Sign up using Facebook.

  GRIFFITHS GAMSAT PDF

Put tda752 on a PCB. When I set input voltage to say mV, the output volume is really low, but there’s no interference.

amplifier – Unexpected results with TDA – Electrical Engineering Stack Exchange

Here is my circuit: By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

The minimal voltage listed in the datasheet is 3 V, typical is 6 V and maximum is 18 V, so this looks a bit strange. Now about my problems: I’ll tda7025 with a PCB and a nF capacitor next.

The gain is set to 20dB with pin 4 being driven at 1Vdc. Curd the word ‘offset’ usually refers to the steady-state DC level – ie: It sounds like you have a perfectly good amplifier that is just missing a heat sink. Here’s the effect of increasing volume on a sine wave: